Downgraded Ps3 and Went to Upgrade Again and Getting a Corrupt

NAND flasher downgrader steps

NOR flasher downgrader steps

Downgrading installation steps

Contents

• 1 Dump
• 2 Checking console capability of running 3.55
  • 2.1 metldr+bootldr sizes
• 3 Patch the dump & Reflash it to the console
  • 3.1 NAND
  • 3.2 NOR
    • 3.2.1 E3 Flasher
• 4 Reinstall firmware in Factory Service Mode
  • 4.1 PUP to use
  • 4.2 Different Factory Service Mode SELFs
    • 4.2.1 NAND
    • 4.2.2 NOR
  • 4.3 Check the logfile
  • 4.4 Getting out of Factory Service Mode
• 5 Dehashing
  • 5.1 QA dehashing
  • 5.2 reFSM dehashing
    • 5.2.1 Remarks

Dump [edit]

Connect your Hardware flashing device and make sure you are getting 100% correct, valid, verified dumps.

Checking console capability of running 3.55 [edit]

Compare the values found in your dump with those in the metldr+bootldr sizes table

If not having a dump, use the MinVer PUP method

Note:

The mention of minimal version praxis on several other wikipages is only a rough indication.

The two most accurate ways are to look at the actual dump and the MinVer PUP method itself, instead of flying blind on SKU tables and datecodes

metldr+bootldr sizes [edit]

You can check metldr and bootldr sizes easily with HxD

• either after extracting flash with Flowrebuilder and opening seperate files
• or by looking in the unextracted Flash dump at the correct offset.

This table lists some common known values for your convenience as quick lookup:

IDPS/Product Code	SKU - Datecode / Manufacturing date	metldr offset		bootldr			Notes	lowest known firmware
0x2F077 (NOR) 0x80877 (NAND)		0x81E (NOR) 0x4081E (NAND)	0x842 (NOR) 0x40842 (NAND)	size	0xFC0002 (NOR) 0x02 (NAND)	0xFC0012 (NOR) 0x12 (NAND)
n/a	CEB-2030 (MPU-501) PROTO	n/a	n/a	28C20	28 BE	28 BE	Patch + FSM = OK	<=0.50.003
01	DEH-Z1010 (TMU-520) SD	14 20	11 3E	2D020	2C FE	2C FE	Patch + FSM = OK	<=0.80.004
01	DECR-1000 (TMU-520) DECR Every DECR manufactured before January 2009 Share the same BL/Metldr revisions	EC 40	0E C0	2A840	2A 80	2A 80	Patch + FSM = OK	<=0.85.010
01	?DEH-H1001-D? (COOKIE13) CEX	EC 40	0E C0	2A830	2A 7F	2A 7F	Patch + FSM = OK	<=0.85.010
01	DEH-H1000A-E (COK-001) DEX	EC 70	0E C3	2A1E0	2A 1A	2A 1A	Patch + FSM = OK	<095.001
01 04	CECHAxx (COK-001) CECHExx (COK-002)	EE 10	0E DD	2A430	2A 3F	2A 3F	Patch + FSM = OK	1.00 1.00
01 02 03 01	CECHAxx (COK-001) with 1.00 from factory CECHBxx (COK-001) CECHCxx (COK-002) DECHAxx (COK-001) DEX	ED A0	0E D6	2A2E0	2A 2A	2A 2A	Patch + FSM = OK	1.00 1.00 1.00 1.00
03	CECHCxx (COK-002) with 1.00 from factory	EB F0	0E BB	30480	30 44	30 44	Patch + FSM = OK	1.00 1.00
01 02 03	CECHAxx (COK-001) CECHBxx (COK-001) CECHCxx (COK-002)	ED E0	0E DA	2A3B0	2A 37	2A 37	Patch + FSM = OK	1.00 1.00 1.00
04 05	Namco System 357 (COK-002) ARC CECHGxx (SEM-001)	E7 B0	0E 77	2E900	2E 8C	2E 8C	Patch + FSM = OK	?1.90? 1.90
05 06	CECHGxx (SEM-001) CECHHxx (DIA-001)	E7 B0	0E 77	2F200	2F 1C	2F 1C	Patch + FSM = OK	2.30 2.30
05 06	CECHGxx (SEM-001) CECHHxx (DIA-001)	E8 C0	0E 88	2EF80	2E F4	2E F4	Patch + FSM = OK	2.30 2.30
06 07	CECHHxx (DIA-001) CECHJxx (DIA-002) with 2.30 from factory - datecode 8B	E8 E0	0E 8A	2EF80	2E F4	2E F4	Patch + FSM = OK	1.97 2.30
03 06 06	CECHExx (COK-002) CECHHxx (DIA-001) CECHMxx (DIA-001)	EA 60	0E A2	2EE70	2E E3	2E E3	Patch + FSM = OK	1.97 1.97
07	CECHJxx (DIA-002) CECHKxx (DIA-002) datecode 8C	EA 60	0E A2	2EE70	2E E3	2E E3	Patch + FSM = OK	2.30
08 07 08	Namco System 357 (VER-001) ARC DECHJxx (DIA-002) DEX CECHLxx / CECHPxx (VER-001)	E8 D0	0E 89	2EAF0	2E AB	2E AB	Patch + FSM = OK	?2.45? 2.16 2.45
08	CECHLxx (VER-001)	E8 D0	0E 89	2EB70	2E B3	2E B3	Patch + FSM = OK	2.45
08 09	CECHLxx (VER-001) with 2.30 from factory - datecode unknown CECH-20xx (DYN-001) with 2.76 from factory, datecode unknown	E8 90	0E 85	2F170	2F 13	2F 13	Patch + FSM = OK	2.30 2.70
09	DECR-1400 (DEB-001) DECR with 2.60 from factory - manufacture date June 09	E8 90	0E 85	2F170	2F 13	2F 13	Patch + FSM = OK	2.60
09	CECH-20xx (DYN-001)	E9 20	0E 8E	2F3F0	2F 3B	2F 3B	Patch + FSM = OK	2.70
0A	CECH-21xx (SUR-001)	E9 20	0E 8E	2F4F0	2F 4B	2F 4B	Patch + FSM = OK	3.20
03 0B 0B	CECHExx (COK-002W) refurbished CECH-25xx (JTP-001) with 3.40 from factory - datecode 0C CECH-25xx (JSD-001) with 3.41 from factory - datecode 0C	E9 20	0E 8E	2F4F0	2F 4B	2F 4B	Patch + FSM = OK	3.40 3.40 3.40
0B 0B	CECH-25xx (JSD-001) with 3.56 from factory - datecode 0D CECH-25xx (JTP-001) with 3.56 from factory - datecode 1A	E9 60	0E 92	2F570	2F 53	2F 53	Patch + FSM = OK	3.50 3.50
0B 0B 0B	CECH-25xx (JTP-001) with 3.56 from factory - datecode 1A (rare) CECH-25xx (JSD-001) with 3.56 from factory - datecode 1B (common) CECH-25xx (JTP-001) with 3.56 from factory - datecode 1B (common)	E9 60	0E 92	2F5F0	2F 5B	2F 5B	(RLOD+)poweroff @ downgrade 355 (3.56+ + spkg fix + signed 3.55 priv : should work) Patch + noFSM = OK	3.56 3.56 3.56
0B 0B 0C	CECH-25xx (JSD-001) with3.60 from factory - datecode 1B CECH-25xx (JTP-001) with3.60 from factory - datecode [N.A.] CECH-30xx (KTE-001) with3.65 from factory - datecode [N.A.]	F9 20	0F 8E	2FFF0	2F FB	2F FB	"metldr.2" (RLOD+)poweroff @ downgrade 3.55 (RLOD+)poweroff @ Patch + noFSM	3.60 3.60 3.60
0C	CECH-30xx (KTE-001) with? from factory - datecode [?]	F9 B0	0F 97	30070	30 03	30 03	"metldr.2" (RLOD+)poweroff @ downgrade 3.55 (RLOD+)poweroff @ Patch + noFSM	?
0C	CECH-30xx (KTE-001) with3.72 from factory - datecode [1C]	F9 B0	0F 97	300F0	30 0B	30 0B	"metldr.2" (RLOD+)poweroff @ downgrade 3.55 (RLOD+)poweroff @ Patch + noFSM	3.72
0D 0D 2C	CECH-40xx (MSX-001) CECH-40xx (MPX-001) CECH-40xx (MSX-001) '12GB'	F9 B0	0F 97	301F0	30 1B	30 1B	"metldr.2" (RLOD+)poweroff @ downgrade 3.55 (RLOD+)poweroff @ Patch + noFSM	4.20 ? 4.22

Patch the dump & Reflash it to the console [edit]

Flowrebuilder : Autopatcher

Flowrebuilder : Autopatcher - completed

For patching you can use:

• Hexeditor (e.g. HxD)
• Flowrebuilder (both NOR + unified NAND)
• in case of Progskeet, latest Winskeet/iSkeet/YASkeet (both NOR + unified NAND)
• BwE NOR/NAND Patcher

NAND + NOR patchfile.txt

NAND [edit]

Use NAND patches only on NAND consoles, not on NOR!

Target area	Patchfile	NAND Offset	Paste length	Remarks
ROS0	patch1 (7 MB)	0x0C0030	0x6FFFE0	CoreOS (prepatched 3.55)
ROS1	patch1 (7 MB)	0x7C0020	0x6FFFE0	CoreOS (SAME as ros0)
trvk_prg0 (0x91800) trvk_prg1 (0x92810) trvk_pkg (0x93800)	patch2 (16 KB)	0x91800	0x4000	one big patch overlapping several revoke area's

(above patches in a single package + autopatcher file: NAND downgrade.rar [1])

NOR [edit]

Use NOR patches only on NOR consoles, not on NAND!

Target area	Patchfile	NOR Offset	Paste length	Remarks
ROS0	patch1 (7 MB)	0x0C0010	0x6FFFE0	CoreOS (prepatched 3.55)
ROS1	patch1 (7 MB)	0x7C0010	0x6FFFE0	CoreOS (SAME as ros0)
trvk_prg0 (0x40000) trvk_prg1 (0x60000) trvk_pkg0 (0x80000) trvk_pkg1 (0xA0000)	rvk-040000 (512 KB)	0x40000	0x80000	one big patch overlapping several revoke area's

(above patches in a single package + autopatcher file: NOR downgrade.rar [2])

E3 Flasher [edit]

Use these instead, otherwise you get into a maze of bytereversing: E3 Manual downgrade patches or use BwE NOR/NAND Patcher

Reinstall firmware in Factory Service Mode [edit]

PSGrade/JIG - in rightmost USB Port - for triggering factory service mode

USBSTICK - content for factory service mode - downgrading

USBSTICK - in rightmost USB Port - for installing in factory service mode

For this step it is required to have the console fully assembled (connected PSU, coolingblock+fan, harddrive, wifi/bt board, blu-ray drive etc).

1. Use the PSGrade/JIG dongle to trigger Factory Service Mode
   • Remove power from the console (rear power switch or remove powercord)
   • Put PSGrade/JIG dongle in the rightmost USB port (closest to the Blu-Ray drive)
   • Power the console so it is in standby (rear power switch or attach powercord)
   • Press power button on front of the PS3 then immediately press eject within ~100ms
   • If powered on correctly your dongle will light up (usually green) and trigger Factory Service Mode. The PSGrade will then power off the console. If it boots into the XMB with a red FSM logo in the corner you are using an old PSGrade.
2. Put the Lv2diag.self (see below) and a pre-patched firmware to install (named PS3UPDAT.PUP) in root of your USB Mass Storage Device and plug it in the PS3 (in the same port as the PSGrade).
3. Turn PS3 on and it will automatically install the firmware you had put there. You will not have anything on the screen, you can only tell it is installing by the flashing USB and PS3's HDD light
4. PS3 will turn itself off after finishing the firmware installation (If it flashes red the firmware did not install correctly).
   A logfile should be present in root of the USB Mass Storage Device with no errors

See also Downgrading with PSgrade Dongle, which also contains alot of ready to use PSgrade HEX files for several dongles.

PUP to use [edit]

Rogero V3.7 (mirror / MD5:8f8166b25d6bed891f292c77de5c4b28)

for noFSM, use 9.99 downgrader instead: MD5:b67747f529d047d63151786544a58b50

or any firmware with prepatched lv1 (no syscon hash checks)        

Note: if your end-goal is a 3.56+ MFW, then it is safer to downgrade first to 3.55. Upgrading in service mode (mostly errors out 0x8002f14e) is never recommended (only lower or same version).

Different Factory Service Mode SELFs [edit]

NAND [edit]

For factory Service Mode install:

• if using the normal lv2diag : Use a NoBD patched PUP (e.g. Rogero NoBD PUP) (to prevent error 0x8002f057)
• if using the jaicrab NoBD lv2diag : Use the Rogero normal PUP - see note below (and redump flash after FSM to check both ROS)

note: since V3 Rogero is only available as noBD, use that one with normal lv2diag.self

NOR [edit]

Use the normal lv2diag and use the Rogero normal PUP

Only when having a console with a broken bluraydrive, you either:

• use the normal lv2diag : Use a NoBD patched PUP (e.g. Rogero NoBD PUP) (to prevent error 0x8002f057)
• use the jaicrab NoBD lv2diag : Use the Rogero normal PUP - see note below

note: since V3.7 Rogero is only available as noBD, use that one with normal lv2diag.self

Filename	Size	Remarks	SHA1	MD5	CRC32	CRC16
Lv2diag.self (365.5 KB)	374272	3.55 in FSM *	1ED037740D67FEBACA6449CABFF4E95400C9E2EE	099F33A7967F99E91C07E870FD78B3DB	9338ABF2	4FCC
Lv2diag.self (227.38 KB)	232832	jaicrab noBD patched	180823003B086D9D49BC7F83BEA9C769BF73A5EA	3615770407C0C3FA00D8CA49C8ADB362	25E85CFB	EDD0

* recommended default choice, see above notes mirrors: http://mir.cr/1HRZ3M2N / http://mir.cr/060LU86N / http://mir.cr/ATL2LSGI / http://www.mediafire.com/download.php?zmcgdgj6sdh87se /

Check the logfile [edit]

XMB red square notification - factory service mode

After installation of the firmware, take the created logfile in root of USB Mass Storage Device and look if it contains errors (pastie the log if you want to ask for help online on IRC)

Tip:

You can boot console to XMB while still in FSM, if you want to be really sure it installed fine.

Remarks:

• If you are using a component cable the image might be garbled.
• If you are using HDMI, you don't have any screenoutput at all after the "press PS-button" message. (note: conflicting reports on HDMI working or not in FSM)

Getting out of Factory Service Mode [edit]

USBSTICK - content for exit factory service mode

If everything went fine without errors, you can take the console out of service mode and enjoy your downgraded console :)

1. Put the Lv2diag.self (see below) in root of your USB Mass Storage Device and plug it in the PS3 (again, in the rightmost USB port).
2. Turn PS3 on, it will trigger Factory Service Mode off and shutdown.

Filename	Size	Remarks	SHA1	MD5	CRC32	CRC16
Lv2diag.self (201.42 KB)	206256	get out FSM	329877CBD47B994EC0AFCEA6AF98114FD9E5128B	7A20BFDAE65EEFB47A4425DB1B52DCDE	72740080	502A

Dehashing [edit]

Goal: To be able to install unpatched firmwares (or 4.2x/4.3x MFW later on) on consoles that where previously on 3.56+ (highly recomended)

You can use either or both QA/reFSM way:

QA dehashing [edit]

1. Patch as normal downgrader (ROS 0/1 + RVK prg/pkg)
2. install prepatched firmware in factory service mode
3. use the lv2diag.self [file2] to exit factory service mode

Above is already done if you just downgraded

Dump the flash first, in case you brick on dehashing, you can easily flash this one back to debrick

1. Install and run QA-toggle and make sure it beeps as written in that readme
   • Note: for above to work, you need a BD drive connected and married to the console (except CECH-25xx and later).
   • Note: to make sure you enabled QA, not accidently disable it, do the button combo (if it shows menu, then console is QA-flagged correct. Remove the QA-toggle package to prevent it from getting QA-flag reset).

     Set your cursor on (not in) Network Settings and press the key combo (all at the same time): L1+L2+L3(press_left_stick)+R1+R2+dpad_down

2. Make sure no disc is inside BD drive and Poweroff console
3. Put unpatched official firmware (e.g. 3.55) on USB Mass Storage device as /PS3/UPDATE/PS3UPDAT.PUP and insert in PS3

   Note: It has to be a firmware without 'downgrader patches'

4. Boot into Recovery Menu, select "6. System Update" to reinstall firmware.
5. If installation finishes without error (there will be no logs you can check!) and boots XMB OK, then dehashing was successful (the really super paranoid people can do step 4 twice to make sure that both ROS are rehashed).
   Congrats, you now finished downgrading and dehashing. Console runs 3.55 and any firmware of choice can be installed, no longer needing to be patched for downgrader.

reFSM dehashing [edit]

1. Patch as normal downgrader (ROS 0/1 + RVK prg/pkg)
2. install prepatched firmware in service mode

Above is already done if you just downgraded

Dump the flash first, in case you brick on dehashing, you can easily flash this one back to debrick

1. Put console in service mode with JIG (in case you left service mode and ran the prepatched firmware in normal mode)
2. Use normal lv2diag.self and unpatched official firmware (e.g. 3.55) on USB Mass Storage device in root and let the system reinstall that in factory service mode (FSM).
3. After installation is finished console will turn off. Check UPDATER_LOG.TXT in root of USB Mass Storage device (it should have "manufacturing updating SUCCESS(0x8002f000)" in end section).
4. If everything is OK, then reinsert USB Mass Storage device and let it install again.
5. After installation is finished console will turn off. Check UPDATER_LOG.TXT in root of USB Mass Storage device (it should have "manufacturing updating SUCCESS(0x8002f000)" in end section).
6. If everything is OK, then console should now be dehashed and no longer brick with any unpatched firmwares.
7. Replace lv2diag.self for he one getting out of service mode and put in root.
8. Power on console, it should turn off and not boot XMB.
9. Remove USB Mass Storage device and boot console normally. If all went well it should load to XMB now. Congrats, you now finished downgrading and dehashing. Console runs 3.55 and any firmware of choice can be installed, no longer needing to be patched for downgrader.

[edit]

• FSM gets you a installer LOG (QA does not)
• FSM does not delete ACT.DAT (QA does)
• FSM can be done without a BD drive with noBD patched firmware (QA needs the BD drive present)
• FSM can be done without seeing XMB or Recovery (QA needs Recovery and XMB for the QA-flagging package)

Both ways require installing nonpatched firmware to dehash syscon bank. QA-flag can be removed/reset (but it is better to keep it flagged) after succesfull dehash, without bricking.

          <domelec> dehash procedure: fsm install ofw            after console turns off take out usb stick and look at log file,             if log is ok then reinsert usb stick and turn on console,            ofw will then reinstall, after console turns off again             take out usb stick and check log, if ok then exit fsm        

          <eussNL> do double FSM OFW, then get out of service mode.  <eussNL> check everything is working  <eussNL> THEN and only THEN, you can install whatever you want, in recovery.  <eussNL> there is no need for factory mode after dehashing complete  <eussNL> in fact, if everything works on OFW 3.55 after dehashing,   <eussNL> you can install Rogero V3.2 in recovery and QA-extra flag it    <eussNL> if OFW 3.55 works then you proven that you dehashed  <eussNL> so after that you can install whatever MFW 3.55 you want        

          <eussNL> If for some reason you cannot dehash because of BD or BT errors           then you can use PS3MFW Builder and the broken Blueray / broken Bluetooth           tasks. Do not select downgrader patches, or you will not dehash!        

          <eussNL> BD error can be persistant if flasher is still attached,            see: http://www.ps3devwiki.com/wiki/Talk:Hardware_flashing#BD_drive_not_found_problem  <eussNL> 3 options: 1. open R7/R8  /  2. remove flasher control lines / 3. remove all flasher wiring        

          <playonlcd> i  think you can update on wiki "dehashing with jaicrab is not recommended              and will not dehash as needed and thus semibrick by syscon hash panic        

v e Hardware Flashers
Prerequisition	Overview· Comparison· Warnings
Hardware flashing	Infectus· Noraliser· Teensy++ 2.0· Progskeet 1.0 / 1.1· Progskeet 1.2· Progskeet 1.21· PNM· PIC32MX· E3
Pin/pad layouts	NAND COK-001· COK-002· COK-002W· SEM-001 NOR layout 1 DIA-001· DIA-002 layout 2 VER-001 layout 3 DYN-001 layout 4 SUR-001· JTP-001· JSD-001· KTE-001 layout 5 MSX-001· MPX-001· NPX-001· PQX-001
Downgrading	Software Dumping· Hardware Dumping· Validating flash dumps· Downgrading with Hardware flasher· Dual Firmware· Problem Solving
Old reference	Downgrade BluRay Playback Issue· Downgrading with PSgrade Dongle· Downgrading with NOR flasher· Downgrading with NAND flasher· E3 Nor dump checker

belvillehisaid.blogspot.com

Source: https://psdevwiki.com/ps3/Downgrading_with_Hardware_flasher

Share this post